|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
an AMP company Low Noise Amplifier 1400 - 2000 MHz Features * * * * * * AM50-0006 SOT-26 .114 .008 2,9 0,2 .075 .008 1,90 0,2 PIN # 1 V2.00 Low Noise Figure: 1.6 dB High Input IP3: -6 dBm at 3 V, 6.5 mA bias High Gain: 18 dB Single Supply: +3 to +8 VDC Low Cost SOT-26 Miniature Plastic Package Adjustable current: 3 to 20 mA with an external resistor .063 +.008 -.004 1,60 +0.20 -0.10 02XY .110 .008 2,80 0,2 Description M/A-COMs AM50-0006 is a high dynamic range, GaAs MMIC, low noise amplifier in a low cost, SOT-26 miniature surface mount, plastic package. It employs external input matching to obtain optimum noise figure performance and operating frequency flexibility. The AM50-0006 also features flexible biasing to control the current consumption vs. dynamic range trade-off. The AM50-0006 can operate from any positive supply voltage in the 3 V to 8 V range. Its current can be controlled over a range of 3 mA to 20 mA with an external resistor. The AM50-0006 is ideally suited for use where low noise figure, high gain, high dynamic range, and low power consumption are required. Typical applications include receiver front ends in PDC1500, DCS-1800, DCS-1900, PHS and other PCN/PCS applications. It is also useful as a gain block, buffer, driver and IF amplifier in both fixed and portable PDC, PHS, and PCN/PCS systems. The AM50-0006 is fabricated using a low-cost 0.5-micron gate length GaAs process. The process features full passivation for increased performance reliability. The AM50-0006 is 100% RF tested to ensure performance specification compliance. .031+.004 -.007 0,79 +0.10 -0.18 .016 +.004 -.002 .002 .002 0,05 0,05 +.004 .006 -.002 .008 MIN 0,20 MIN +.008 .043 -.004 1,10+0.20 -0.10 0,40 +0.10 -0.05 +0.10 0,15 -0.05 Ordering Information Part Number AM50-0006 AM50-0006TR AM50-0006PDC AM50-0006PCS Package SOT-26 Plastic Package Forward Tape and Reel* 1400-1520 MHz Designers Kit 1700-2000 MHz Designers Kit * If specific reel size is required, consult factory for part number assignment. Electrical Specifications : TA=+25C, Z0 = 50 , PIN = - 30 dBm 1 Parameter Test Conditions Units Min. 1500 MHz Typ. 18 1.60 2.2:1 1.5:1 Max. 20 2.00 Min. 15 1900 MHz Typ. 17.5 1.65 1.5:1 1.5:1 0 -6.0 35 10 4.5 6.5 10 Max. 20 2.00 Gain Noise Figure Input VSWR Output VSWR Output 1 dB Compression Input IP3 Reverse Isolation VDD = 3 Volts VDD = 3 Volts dB dB 15 VDD = 3 Volts VDD = 3 Volts dBm dBm dB 1 -5.0 35 6.5 Drain current VDD = 3 Volts mA 4.5 1. Using external 120 resistor. See functional block diagrams on pages 2 and 5. M/A-COM, Inc. North America: Specifications Subject to Change Without Notice. Tel. (800) 366-2266 Asia/Pacific: Tel. +81 3 3263-8761 Fax +81 3 3263-8769 1 Europe: Tel. +44 (1344) 869-595 Fax +44 (1344) 300-020 Fax (800) 618-8883 Low Noise Amplifier Absolute Maximum Ratings Parameter V,, Input Power Current Channel Temperature +10 VDC +17 dBm 30 mA 1 AM50-0006 Pin Configuration Pin No. 1 2 Pin Name GND Rext Cext 3 4 5 6 IN V,, GND OUT Description RF and DC Ground External Current Control By-Pass Capacitor RF Input of the Amplifier Positive Supply Voltage RF and DC Ground RF Output of the Amplifier V2.00 Absolute Maximum ! +150C -40C to +85C -65C to +150C Operating Temperature Storage Temperature 1. Exceeding any one or combination of these limits may cause permanent damage. 2. When pin #2 is used to increase current. (See note 5.) 3. Thermal resistance (jc) = +150C/W. Functional Block Diagram For 1700-2000 MHz Operation V DD Input Reflection Coefficient 1700-2000 MHz Operation Freq. 1700 MHz 0.699 48.47 1850 MHz 0.674 38.68 2000 MHz 0.649 29.27 in (mag) in (ang) L2 in C1 TRL 3 4 C2 External Circuitry Parts List For 1700-2000 MHz Operation 4 Part 6 Value 47 pF 470 pF 2.7 nH 22 nH See Note 5 470 pF Purpose DC Block By-Pass Tuning RF Choke Current control By-Pass RF OUT C1 C2 RF IN L1 1,5 L1 L2 C3 R1 (See note 5) R1 C3 Recommended PCB Configuration For 1700-2000 MHz Operation Layout View PIN # 1 4. All external circuitry parts are readily available, low cost surface mount components (.060 in. x .030 in. or .080 in. x .050 in.). 5. Pin 2 allows use of an external resistor to ground for optional, higher current. For I,, ~ 5 mA, R1 = 150 ohms; I,, ~ 6.5 mA, R1 = 120 ohms; I,, ~ 20 mA, R1 = 27 ohms. RF OUT Cross Section View RF Traces + Components R1 L1 C3 U1 L2 C2 V DD RF Ground DC Routing Customer Defined TRL C1 RF IN 2 Specifications Subject to Change Without Notice. The PCB dielectric between RF traces and RF ground layers should be chosen to reduce RF discontinuities between 50 lines and package pins. M/A-COM recommends an FR-4 dielectric thickness of 0.008 (0.20 mm) yielding a 50 line width of 0.015 (0.38 mm). The recommended RF metalization is 1 ounce copper. M/A-COM, Inc. Europe: Tel. +44 (1344) 869-595 Fax +44 (1344) 300-020 North America: Tel. (800) 366-2266 Fax (800) 618-8883 Asia/Pacific: Tel. +81 3 3263-8761 Fax +81 3 3263-8769 Low Noise Amplifier Test Conditions: T)= +25C, Z = 50 GAIN vs. FREQUENCY 22 AM50-0006 V2.00 Typical 1700-2000 MHz Performance Data (when matched at input with in, see page 2) , unless otherwise specified. INPUT IP3 vs. FREQUENCY 10 5V,20mA Input IP3 (dBm) 20 Gain (dB) 5V , 20m A 5 3V,6.5mA 18 0 16 3V,5mA 14 12 1.7 1.8 1.9 2.0 2.1 2.2 3V , 6.5m A -5 -1 0 1.7 1.8 1.9 3V, 5mA 2.0 Frequency (GHz) F r e q u e n c y (G H z ) NOISE FIGURE vs. FREQUENCY (Bias = 3V, 6.5mA) 2.5 VSWR vs. FREQUENCY (Bias = 3V, 6.5mA) 3.0 Noise Figure (dB) 2.5 2.0 Output 8594 2.0 Input 1.5 1.5 1.0 1.7 1.8 1.9 2.0 2.1 2.2 1.0 1.7 1.8 1.9 2.0 2.1 2.2 Frequency (GHz) Frequency (GHz) OUTPUT P1dB vs. FREQUENCY 15.0 1 dB Compression (dBm) INPUT IP3 vs. DRAIN CURRENT (Freq. = 1900 MHz) 10 5V, 20mA Input IP3 (dBm) 10.0 5 5V 5.0 3V, 6.5mA 0 0.0 -5 3V -5.0 1.7 1.8 1.9 3V, 5mA 2.0 Frequency (GHz) -1 0 5 10 15 20 D r a in C u r r e n t (m A) M/A-COM, Inc. North America: Specifications Subject to Change Without Notice. Tel. (800) 366-2266 Fax (800) 618-8883 Asia/Pacific: Tel. +81 3 3263-8761 Fax +81 3 3263-8769 3 Europe: Tel. +44 (1344) 869-595 Fax +44 (1344) 300-020 Low Noise Amplifier Test Conditions: Bias = 3V, 6.5 mA, Z = 50 GAIN vs. TEMPERATURE 22 AM50-0006 V2.00 Typical 1700-2000 MHz Performance Data cont. (when matched at input with in, see page 2) , unless otherwise specified. NOISE FIGURE vs. TEMPERATURE 3.0 20 Gain (dB) Noise Figure (dB) -40C 2.5 + 85C + 25C 18 2.0 16 1.5 14 +25C +85C 2.0 2.1 2.2 1.0 -40C 0.5 1.7 1.8 1.9 2.0 2.1 2.2 F r e q u e n c y (G H z ) 12 1.7 1.8 1.9 Frequency (GHz) Designers Kit AM50-0006PCS The AM50-0006 Designer's Kit allows for immediate evaluation of M/A-COM's AM50-0006 tuned for 1700-2000 MHz operation. The Designers Kit includes an AM50-0006, an evaluation board, and a floppy disk containing typical performance data and a DXF files of the recommended PCB layouts. The evaluation board consists of the recommended external surface mount circuitry, RF connectors, and a DC multi-pin connector, all mounted to a multi-layer FR-4 PCB. The AM50-0006PCS evaluation PCB is illustrated below with all functional ports labeled. Evaluation PCB + RF Connector Losses Port Reference LNA Input LNA Output Approximate RF Loss 0.15 dB @ 1.90 GHz 0.15 dB @ 1.90 GHz The DC connector on the Designers Kit PCB allows convenient DC line access. This is accomplished by of the one or more of the following methods: 1. A mating female multi-pin connector (Newark Electronics Stock # 46F-4658, not included). 2. Wires soldered to the necessary pins (not included). 3. Clip leads (not included). AM50-0006PCS EVALUATION BOARD 4 Specifications Subject to Change Without Notice. North America: Tel. (800) 366-2266 Fax (800) 618-8883 Asia/Pacific: Tel. +81 3 3263-8761 Fax +81 3 3263-8769 M/A-COM, Inc. Europe: Tel. +44 (1344) 869-595 Fax +44 (1344) 300-020 Low Noise Amplifier Absolute Maximum Ratings Parameter V,, Input Power Current Channel Temperature +10 VDC +17 dBm 30 mA 1 AM50-0006 Pin Configuration Pin No. 1 2 Pin Name GND Rext Cext 3 4 5 6 IN V,, GND OUT Description RF and DC Ground External Current Control By-Pass Capacitor RF Input of the Amplifier Positive Supply Voltage RF and DC Ground RF Output of the Amplifier V2.00 Absolute Maximum ! +150C -40C to +85C -65C to +150C Operating Temperature Storage Temperature 1. Exceeding any one or combination of these limits may cause permanent damage. 2. When pin #2 is used to increase current. (See note 5.) 3. Thermal resistance (jc) = +150C/W. Functional Block Diagram For 1400-1520 MHz Operation V DD External Circuitry Parts List For 1400-1520 MHz Operation 4 Part C1 Value 47 pF 470 pF 10 nH 3.9 nH 22 nH See Note 5 470 pF Purpose DC Block By-Pass Tuning Tuning RF Choke Current control By-Pass L3 C2 C2 L1 L2 C1 L1 3 4 6 L2 RF OUT L3 R1 C3 RF IN 2 1,5 R1 (see note 5) C3 4. All external circuitry parts are readily available, low cost surface mount components (.060 in. x .030 in. or .080 in. x .050 in.). 5. Pin 2 allows use of an external resistor to ground for optional, higher current. For I,, ~ 5 mA, R1 = 150 ohms; I,, ~ 6.5 mA, R1 = 120 ohms; I,, ~ 20 mA, R1 = 27 ohms. Recommended PCB Configuration For 1400-1520 MHz Operation Layout View Pin #1 C3 R1 L3 Cross Section View RF OUT RF Traces + Components RF Ground DC Routing Customer Defined L2 L1 C2 V,, C1 The PCB dielectric between RF traces and RF ground layers should be chosen to reduce RF discontinuities between 50 lines and package pins. M/A-COM recommends an FR-4 dielectric thickness of 0.008 (0.20 mm) yielding a 50 line width of 0.015 (0.38 mm). The recommended RF metalization is 1 ounce copper. RF IN M/A-COM, Inc. North America: Specifications Subject to Change Without Notice. Tel. (800) 366-2266 Fax (800) 618-8883 Asia/Pacific: Tel. +81 3 3263-8761 Fax +81 3 3263-8769 5 Europe: Tel. +44 (1344) 869-595 Fax +44 (1344) 300-020 Low Noise Amplifier Typical 1400-1520 MHz Performance Data (when matched as shown on page 5) Test Conditions: T)= +25C, Z = 50 GAIN vs. FREQUENCY 22 AM50-0006 V2.00 , unless otherwise specified. INPUT IP3 vs. FREQUENCY 10 20 18 Input IP3 (dBm) 5V, 20mA Gain (dB) 5 0 5V,20mA 16 3V,6.5mA 3V, 6.5mA 14 -5 3V, 5mA 12 1.30 1.35 1.40 1.45 1.50 1.55 1.60 -10 1.35 Frequency (GHz) 3V,5mA 1.40 1.45 Fre que ncy (GHz ) 1.50 1.55 NOISE FIGURE vs. FREQUENCY (Bias = 3V, 6.5mA) 2.5 VSWR vs. FREQUENCY (Bias = 3V, 6.5mA) 3.0 Noise Figure (dB) 2.5 2.0 Input 8594 2.0 Output 1.5 1.5 1.0 1.35 1.40 1.45 Frequency (GHz) 1.50 1.55 1.0 1.30 1.35 1.40 1.45 1.50 F requency (GHz ) 1.55 1.60 OUTPUT P1dB vs. FREQUENCY 15 1 dB Compression (dBm) INPUT IP3 vs. DRAIN CURRENT (Freq. = 1500 MHz) 10 5V, 20mA 3V, 6.5mA Input IP3 (dBm) 10 5 #8 5 0 0 -5 !8 -5 1.35 3V, 5mA -10 1.40 1.45 Frequency (GHz) 1.50 1.55 5 10 15 20 Dra in Curre nt (m A) 6 Specifications Subject to Change Without Notice. North America: Tel. (800) 366-2266 Fax (800) 618-8883 Asia/Pacific: Tel. +81 3 3263-8761 Fax +81 3 3263-8769 M/A-COM, Inc. Europe: Tel. +44 (1344) 869-595 Fax +44 (1344) 300-020 Low Noise Amplifier Test Conditions: Bias=3V, 6.5 mA, Z = 50 GAIN vs. TEMPERATURE 22 AM50-0006 V2.00 Typical 1400-1520 MHz Performance Data cont. (when matched as shown on page 5) , unless otherwise specified. NOISE FIGURE vs. TEMPERATURE 3. 0 Noise Figure (dB) 20 Gain (dB) -40C 2. 5 +85C +25C 18 2. 0 16 +25C +85C 1. 5 14 1. 0 -40C 1. 40 1. 45 F re q u e n cy (G Hz ) 1. 50 1. 55 12 1.30 1.35 1.40 1.45 1.50 1.55 1.60 0. 5 1. 35 Frequency (GHz) Designers Kit AM50-0006PDC The AM50-0006 Designer's Kit allows for immediate evaluation of M/A-COM's AM50-0006 tuned for 1400-1520 MHz operation. The Designers Kit includes an AM50-0006, an evaluation board, and a floppy disk containing typical performance data and a DXF files of the recommended PCB layouts. The evaluation board consists of the recommended external surface mount circuitry, RF connectors, and a DC multi-pin connector, all mounted to a multi-layer FR-4 PCB. The AM50-0006PDC evaluation PCB is illustrated below with all functional ports labeled. Evaluation PCB + RF Connector Losses Port Reference LNA Input LNA Output Approximate RF Loss 0.1 dB @ 1.50 GHz 0.1 dB @ 1.50 GHz The DC connector on the Designers Kit PCB allows convenient DC line access. This is accomplished by of the one or more of the following methods: 1. A mating female multi-pin connector (Newark Electronics Stock # 46F-4658, not included). 2. Wires soldered to the necessary pins (not included). 3. Clip leads (not included). AM50-0006PDC EVALUATION BOARD M/A-COM, Inc. North America: Specifications Subject to Change Without Notice. Tel. (800) 366-2266 Fax (800) 618-8883 Asia/Pacific: Tel. +81 3 3263-8761 Fax +81 3 3263-8769 7 Europe: Tel. +44 (1344) 869-595 Fax +44 (1344) 300-020 |
Price & Availability of AM50-0006 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |